https://futex.re/mediawiki/index.php?action=history&feed=atom&title=2.16_Cr%C3%A9ation_et_gestion_du_bonding
2.16 Création et gestion du bonding - Historique des versions
2026-04-07T06:15:09Z
Historique des versions pour cette page sur le wiki
MediaWiki 1.39.17
https://futex.re/mediawiki/index.php?title=2.16_Cr%C3%A9ation_et_gestion_du_bonding&diff=2191&oldid=prev
Futex : /* Afficher la carte slave */
2013-06-14T13:34:32Z
<p><span dir="auto"><span class="autocomment">Afficher la carte slave</span></span></p>
<p><b>Nouvelle page</b></p><div>== Configuration du bonding==<br />
<br />
Sous Suse, Redhat, CentOS<br />
# cat ifcfg-bond0<br />
BOOTPROTO='static'<br />
STARTMODE='auto'<br />
USERCONTROL='no'<br />
BONDING_MASTER='yes'<br />
BONDING_MODULE_OPTS='mode=802.3ad miimon=100'<br />
BONDING_SLAVE0='eth0'<br />
BONDING_SLAVE1='eth2'<br />
IPADDR='10.68.82.66/24'<br />
# cat ifcfg-eth0<br />
BOOTPROTO='none'<br />
STARTMODE='auto'<br />
USERCONTROL='no'<br />
ETHTOOL_OPTIONS='autoneg on'<br />
<br />
Sous Debian<br />
# cat /etc/network/interfaces<br />
auto eth0<br />
auto eth1<br />
auto bond0<br />
iface bond0 inet static address 192.168.0.1network 255.255.255.0 gateway 192.168.0.254 up <br />
/sbin/ifenslave bond0 eth0 eth1<br />
<br />
mode 0 ou équilibrage de charge<br />
mode 1 ou sauvegarde active<br />
mode 2 ou balance XOR<br />
mode 3 ou broadcast<br />
mode 4 ou 802.3ad<br />
mode 5 ou Traffic load balancing<br />
mode 6 ou Adaptive load balancing<br />
<br />
== Afficher le status du bonding ==<br />
# cat /proc/net/bonding/bond0<br />
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)<br><br />
Bonding Mode: IEEE 802.3ad Dynamic link aggregation<br />
Transmit Hash Policy: layer2 (0)<br />
MII Status: up<br />
MII Polling Interval (ms): 100<br />
Up Delay (ms): 0<br />
Down Delay (ms): 0<br><br />
802.3ad info<br />
LACP rate: slow<br />
Aggregator selection policy (ad_select): stable<br />
Active Aggregator Info:<br />
Aggregator ID: 1<br />
Number of ports: 2<br />
Actor Key: 17<br />
Partner Key: 34476<br />
Partner Mac Address: 00:23:04:ee:bf:2d<br><br />
Slave Interface: eth0<br />
MII Status: up<br />
Speed: 1000 Mbps<br />
Duplex: full<br />
Link Failure Count: 2<br />
Permanent HW addr: d4:ae:52:e8:18:17<br />
Aggregator ID: 1<br />
Slave queue ID: 0<br><br />
Slave Interface: eth2<br />
MII Status: up<br />
Speed: 1000 Mbps<br />
Duplex: full<br />
Link Failure Count: 1<br />
Permanent HW addr: d4:ae:52:e8:18:1b<br />
Aggregator ID: 1<br />
Slave queue ID: 0<br />
<br />
== Afficher la carte slave ==<br />
(marche pas en LACP, normal...)<br />
# cat /sys/class/net/bond0/bonding/active_slave<br />
eth1<br />
<br />
# cat /sys/class/net/bond0/bonding/slaves<br />
eth0 eth1<br />
<br />
== Ajouter une carte du bonding ==<br />
<br />
# ifenslave -c bond0 eth0<br />
# echo +eth0 > /sys/class/net/bond0/bonding/slaves<br />
<br />
== Retirer une carte du bonding ==<br />
<br />
# ifenslave -d bond0 eth0<br />
# echo -eth0 > /sys/class/net/bond0/bonding/slaves<br />
<br />
== Module bonding ==<br />
Le module bonding doit être chargé<br />
# lsmod | grep bond<br />
<br />
== Démarrer le bonding ==<br />
<br />
# /etc/init.d/network start<br />
Bringing up loopback interface: [ OK ]<br />
Bringing up interface bond0: [ OK ]<br />
bonding 139865 0</div>
Futex